Scammer

Banned
0638kah_20.jpeg

CANADA

12766060310.jpg

USA

MANUAL
View attachment dongle American.pdf

NEW in BoX

802.11G Wireless Dongle for: Captive Works , COOLSAT , Viewsat

The X-FTA Dongle, has menu so you can put your username and password, SSSP protocol.

Wireless Internet Key Sharing Router for Free to Air Satellite Receivers



Our Wirless IKS Router can provide Card Sharing aka IKS for the following receivers

Captive works 600s, 600sp, 650s, 700s and 800s models

Coolsat 4000,5000 and 6000 models

Viewsat 9000,Viewsat maxx HD, Viewsat Ultra

Azbox Evo XS,S700B,S710USB,S720USB models

And many other SSSP compatible receivers.

also compatible with AVR or Atmega (experts only), no more cable!,

supports distances of 30 meters indoors. (Not for SV)



The router is very easy to configure through its web interface menu and you can be connected and running to your satellite receiver in as little as 5 minutes.

There is no need to run any software on your computer and the router will connect to your wireless router.

You can have one wireless IKS router for each satellite receiver to free your self from running annoying cables or expensive homeplugs.

You can also use the router as a wireless bridge for your blu-ray player or xbox 360 and connect up to 5 devices at once to the router with almost no configuration.
 
Last edited by a moderator:

Lorney

New member
I live in Canada and I have a networking bell router for my high speed internet. My ip address is 192.168.2.1 for main router when I hook up my new XFTA wireless G router, connect to the wlan port, wait and then go to my computer and using firefox punch in the http:192.168.1.1 it doen't come up to gargoyle page it comes up to a list of 192.168.1.1 that you can click on but none of them are the gargoyle page you are talking about. You say this XFTA has a menu on it can you tell me how to access it.
Thank you Lorney
 

longjon

New member
I to own one of these routers the default password is password
but what I'm wondering is it possible to speed this bad boy up
like cpu or tx power and it does have a nice scanning ssid feature
though
 

nivlacgm

New member
hello my name is nivlacgm i was trying to configure my wireless router g dongle after i went to the connection page and select the wireless bridge and set the subnet of my primary router i accidental entered the ap/gateway ip address and press save, i then realized that i should not have gone so far so i went back to ap/gateway and click removed then i press save. after that when i entered the 192.168.1.1 or 192.168.1.2 the number i change it does not open the page it keeps telling me time out. can anyone tell me what i can do to fix this problem thanks.
 

askendria

New member
hello my name is nivlacgm i was trying to configure my wireless router g dongle after i went to the connection page and select the wireless bridge and set the subnet of my primary router i accidental entered the ap/gateway ip address and press save, i then realized that i should not have gone so far so i went back to ap/gateway and click removed then i press save. after that when i entered the 192.168.1.1 or 192.168.1.2 the number i change it does not open the page it keeps telling me time out. can anyone tell me what i can do to fix this problem thanks.

I don't own this router but you may have to reset your router to factory condition and start all over again, that's I'll do if I make any mistakes.

Good luck.
 

askendria

New member
hello my name is nivlacgm i was trying to configure my wireless router g dongle after i went to the connection page and select the wireless bridge and set the subnet of my primary router i accidental entered the ap/gateway ip address and press save, i then realized that i should not have gone so far so i went back to ap/gateway and click removed then i press save. after that when i entered the 192.168.1.1 or 192.168.1.2 the number i change it does not open the page it keeps telling me time out. can anyone tell me what i can do to fix this problem thanks.

I don't own this router but you may have to reset your router to factory condition and start all over again, that's I'll do if I make any mistakes.

Good luck.
 

Osteele

New member
What is the make and model of this dongle. This is very important as we will require that info when flashing it with DD-WRT, OpenWRT, Tomato, Gargoyle, etc...

I await your response. Thank you
 
Top