CASPER

New member
Loading Your Pansat 2700




this is a better explain procedure which I included our links for best results

1). Turn your 2700 "OFF" via rear switch.

2). Connect the RS232 null modem cable to the receiver and Com1 port of your computer. (Use Com2 if not Com1 is not available). Note: 2500 used a straight serial cable for downloads, THIS SERIAL CABLE WILL NOT WORK!!!. You must use a Null Modem serial cable, or a straight serial cable with a "null" adapter.


3). Plug in the receiver, Turn your 2700 "ON" via the rear switch, and see that the “On” is indicated on the LED on the receiver.
4). Run the Downloader X-87BL Loader v27[1].02 [X-87BL] [pansat2700A].exe) from the new created folder.
5. Click the App File only button, browser and select the “latest update” file, example
x-87bl_071204_b75_226_api Example only then click the Open button.


Note: It is highly recommended that you make sure you have the b-75 upgrade on receiver,when powered on in front u should see b-75 on screen at startup

click here for the b-75 upgrade,,if needed
https://preferredbypete.com/2700-files/1185-b75-boot-full-upgrade-kit-pansat.html

Click HERE for the latest 2700 files!!
https://preferredbypete.com/2700-files/4217-pansat-2700a.html

6. Double check and make sure the cable is securely connected.
7. Click the Download button, wait until the “Download Completed!!” is displayed. Watch the LED on the receiver, it should reboot itself, wait until the “On” display.
8). Wait for unit to finish flash, DO NOT INTERUPT!
9). When receiver reboots and displays “On” wait a few more secs until you see the "Download Complete" popup on your pc. Many people unplug too soon!
You are now done with the software update.



Connecting the receiver to the TV.

10). Connect all the RCA cable from the TV to the receiver, connect the R6 Cable from the dish or switch to the IF input of the receiver. Plug in the power cord from the receiver to an AC outlet.
11). You should see the Language Menu on the TV screen, select English.

Satellite Setup

Note : The following steps 12...24 assumes you are using Dish 500 and Legacy Dual LNBs.

I connected my Dish 500 Legacy Dual LNB 119 cable to the LNB1 of the DISEqC, then I connected my LNB 110 cable to the LNB2 of the DISEqC switch.
12). Goto the Installation Option, enter “0000” for p*********word
13). Goto the Antenna setup Option,
14). Select satellite you want (birds Echo8.6/Ku at 110W and Echo7/Ku at 119W are the Dishnet birds), press the OK button. DO NOT select more then one satellite if you only have one dish with one single lnb
15). LNB Type: select “Standard”
16). LNB Local-Freq: enter “11250”
17). 22kHz: OFF
18). See above note: DiSeqC: 0, if you have two lnbs on the dish or two dish then change it to the correct lnb #1, #2, so on...
19). Skew: 45
20). TP: leave it as is
21). Check the Level= highest as you can, and Quality= highest as you can (adjust the dish slightly to improve the signal strength)
22). If you get no quality level on these transponders, try others before giving up. Not all transponders are transmitting all the time. MAKE SURE THE CABLE IS PLUGGED INTO THE "IF INPUT" PORT ON THE BACK OF THE RECEIVER! Plug the other end directly into the LNB on your Dish.
23). Readjust your dish if you still not getting any quality signal
24). Press the Exit button, press OK to save setting


TO SET DEFAULT KEYS.

A.Go to Main Menu (Bins 132 and later, select channel 8282, proceed to step "E")
B.Go to Parental Control
C.Go to Second Pin entry line
D4.Enter 0000 (if 0000 does not work, enter 1668)
E.At "CAS SYSTEM" menu.
F.Scroll down to Set default key button and press it
G.Exit out



Scanning for Channels

25). Go back to the Installation Menu
26). Go to Satellite Scan, press OK, select the satellite to scan using the left or right vol button(it should turn RED). Press OK to start the scanning.

27). After you have completed the setup and tune to a channel...PLEASE NOTE: the latest sw/bins with Autoroll featrure may take up to 15 minutes to locate and set the keys for each Sat provider. Progress will show on screen (sometime the "progress screen" does not reach 100%, don't be concerened, the keys ARE FULLY LOADED.)

28). to get the dish lineup press sat button on remote,choose echo pkg..

After that.....WATCH TV

best of luck
 
Last edited:
Top