Status
Not open for further replies.

CASPER

New member
Controller Setup and Codes

as posted by haddad287.

Code input
1. Turn on the device which you planning to program
2. Find the code from the code list to match the brand of your device.
3. Press "SET" button until 3 seconds later, then LED will be light on.
4. Press the device function button( ex. TV), then the LED will light once.
5. Input the 3 digi code which matches the device in the list, the LED will blink once for each code. If the code is valid for this device, the LED will be off, means the code is fit for this device. If the code is not valid, therj the LED will be off after blink some times, means the code is not correct for this device, need to input new code..
6. Now to test whether the RCU can control the device, if can't, return back to the code setup procedure, and input other code that supposed to match this brand device, if all the code under this brand can't control this device, you need to try the following way by code searching, you may be able to find the code.
7. Write down the correct code for next time use.

Manual codesearch
Code searching means starting from the current device by pulsing 1 to continue search, one time "POWER" one time plus 1 to the code.
1. Press "SET" and hold it for 3 seconds, then LED will be light.
2. Press the function button (ex.TV) , LED will blink once
3. Aim the RCU to the device (ex. TV) and press "POWER" button, one time "POWER" you will get LED blink once..
4. When it switch off the device, means the code you input is correct, then press"EXIT" and save the code, LED will be off.

If you have problems with tv and dvd hold SET down for 3 seconds while holding SET push TV or DVD while SET is being pushed. Led light on TV or DVD should stay on, then put code in.

Code auto setup
1. Press"SET" and hold for 3 seconds, LED will be on
2. Press the function button(ex.TV), LED will blink once.
3. Aim the RCU to the device (ex.TV) and press"POWER" button once and release.
4. When it switch off the device, means the code you input is correct, then press"EXIT" and save the code, LED will be off.

Code Display Setup
1. Press "SET" and hold for 3 seconds, LED will be on,
release the button.
2. Press the function button (ex. TV), LED will blink once.
3. Press "SET" button again, LED will blink once.
4. Press any numeric button, when you press one number and make the LED blink once, this number should be the first one in the code.
5. Repeat the above 4, take the same way to find the second and third number for this code. When you find the third number, the LED will be off.

Codes
37 Sanyo 311
38 Sears 812
39 Sharp 907
40 Sony 902,414
41 Superscan 812
42 tatung 709,421
43 Tevion 421
44 Toshiba 618,719
45 Viewsonic 206,808
46 Vizio 709
47 White Westinghouse 215
48 Yamaha 618
49 Zenith 606,409,714,507

HDTV
1 Go VideoHDT100 662
2 Hitachi 61HDX98B 864
3 Hughes HTL-HD 362,864,765
4 Hughes HIRD-E8 362,864,765
5 LG LSS-3200A 362,864,765
6 LG-HTL-HD 362.864.765
7 Mitsubishi SR-HD5 864
8 Mitsubishi SRHD400 864
9 Mitsubishi SRHD500 864
10 Motorola HDT10 463
11 Philips DSHD800R 864
12 Pioneer SH-D505 062
13 Proscan PSHD 105,265
14 RCAHD65W20
15 RCAPSHD105
16 RCADTC-100
17 RCADTC-210
18 Samsung SIR-T165 959
19 Samsung SIR-T351 959
20 Samsung SIR-TS160 563
21 Samsung SIR-TS360 563
22 SonySATHDlOO 9631
23 SonySATHD200 9631
24 SonySATHDSOO 96^
25 SYLVANIA6900DTD 759
26 Toshiba DST3000 362.765
27 Toshiba DST3100 362.765
28 Toshiba DW65X91 362.765
29 Zenith HDSAT420 065
30 Zenith HDSAT520 065
31 Zenith DTV1080 065

AUX<Laser Disc>
1 DENON 132
2 PIONEER 132
3 PROSCAN 432
4 RCA 432
5 SANYO 824
6 SONY 933
7 ZENITH 824

AUX<HomeAutoma:
1 GEHOMEMINDER
2 HOMEAUTOMATIONj

end c/p
 
Status
Not open for further replies.
Top