ramireddy

New member
Hi,

After I bougtht coolsat 6000 first 5 min my channels ( 110, 119 ) worked fine. After 5 min I didn't get any channel so I tried to rescan 110 and 119 channels. Now my coolsat 6000 always pointing to 110 satlite. I used the correct options and played all the options. My coolsat is not pointing to 119 or 121 satilites at all. Is any one have any idea why my coolsat not pointing to 119 satilite.

Any help would be great....
 
Last edited:

darklist

VIP Member
fix for coolsat 6000 chanel scramble for dish manual key entry
go to menu,go to autoroll options,Set Echostar Autoroll to no,set Bev autoroll to no, then save changes. Now you will have to exit back and manually set your keys. to do this go to channel 8282. You will see edit keys top left corner. Below that you should see some boxes labled 1,2,3,etc. 1 should be nagravision

cas should be NAgravision
Ident should be Dish network (0001)


I hope this will help and should get people back up and running it worked for the most


darklist.
 

Domando1069

VIP Member
Also make sure that your settings for your DiSeqC Switch are correct. If this doesn't work let us know so we can get you up and running
 
Last edited by a moderator:

ramireddy

New member
Hi,

Today I tried with the options that you told and it didn't work for me. Still my dish pointing to 110 satilite only.

Here are the options that I tried.

1) Echostar Autoroll --> fff
2) Bev autoroll --> Off
3) saved the above options
4) Checked keys ( by going 8282 channel). Keys are already there . So I scanned and it didn't work for me.
5) Reentered the keys and scanned and it didn't work for me.
6) I tried all the options in DiSeqC Switch

No luck. Still pointing to 110 channel only. I will appriciate if you help me on this issue.
 

darklist

VIP Member
Go to antenna setup and see echo 7 (119) and check you frequency it should be 11250 and lnb type it depend what type of dish you have out side most likely standard , and check the cable from your dish (lnb) to the switch and see if you can bypass the switch and go directly to your receiver and see if you have working channel on 119 if you do ?..that tells you the switch is bad and if not try to scan ,, it can only be 2 things your signal is not good or you lnb is bad ,,, let me know what dish you have and what lnb you have on the dish ....
 
Last edited by a moderator:

ramireddy

New member
Hi,

Where is antenna setup ? I don't see any antenna setup on the remote. Could you tell me more details about this ?
 

ramireddy

New member
Hi,

My coolsat not pointing to all satilites ( 110,119). Always either it is pointing to 110 or 119. If I reset data base and If I scan it will point all to 110 and it never points to 119. Next day If I reset again and If I scan it may point to 119 and it won't point to 110 at all.

So finally my dish pointing to either 110 or 119 not both? Is any one have any idea why my dish not pointing to both satilites.

I played all the options but no luck..

I will greatly appriciate if any one provide any sugession to fix the problem.
 

ramireddy

New member
Hello,

Any help on the problem that I have. Still my coolsat 6000 pointing to 110 satilite only. It is not pointint to 119 or 121 at all.

Right now I have reciever with dish network and I am getting all channels with that reciever. If I switch my dish network reciever to coolsat 6000 I am not getting 119 channels at all because coolsat 6000 pointing to 110 satilite only.
 
Last edited:
Top