rebooting

  1. H

    9500 and 8 psk questions/problems

    Have read pretty much all of the installation guides and tips/tricks posted everywhere. But can not figure out this problem, hopefully it is something simple. Have a 9500 works great with green board installed, picks up lots of various channels and runs for hours with no problems. Remove...
  2. S

    Limesat Original Factory Bin file v1.03

    Load this file via Loader Program, Null Modem Cable and RS232 Port to correct Boot Loader Corruptions. Here are the Directions.---------1) Start the Limesat_Loader program on Computer and set the com port.Use Null Modem Cable,Hook up the cable to the RS232 Port of the receiver. 2) Select...
  3. T

    Boot Loop Problem

    When I power unit on it alternates flashing 0000 then boot then a colon and repeats forever. I tried leaving it unplugged for over two weeks, still same result. I hooked up a null modem cable and it will download s/w and count down till it gets to A799 then flashes e010. Tried several factory...
  4. N

    Down?

    Anyone else down right now?
  5. 1

    Do Not Reboot

    As the title states do not reboot your receiver or you will be stuck with "OFF SERVICE" the network will show as connected. This is a problem with users rebooting there receivers and not being able to reconnect to the server. This has apparently been reported and has been happening since as...
  6. W

    Nano premium up or down only

    was watching tv went scrambled wrestling was good last night
  7. Y

    Problem with iTunes 7.1.1?

    I am using iTunes 7.1.1, running on a Sony Vaio with Windows XP. Everything has worked well until recently. I had run a recording program AUDACITY. The next time I attempted to open iTunes I got the message "iTunes can not run because it has detected a problem with your audio configuration."...
  8. B

    How to Reboot SATZEN Z300 correctly trying resolve issues.

    -------------------------------------------------------------------------------- How to correctly reboot your SATZEN Z300 system (in 7 magic steps) There are a lot of posts kicking around, concerning IKS enabled units losing their IP's ect and or getting disconnected from the 'net' and being...
  9. BROWNNOSE

    [Attention] iHub How to Get rid of v82, and flash 1.4 successfully,works 100%

    C&P (from another site) Works great, just follow the instructions. What exactly will these steps do for me if everything works out? 1. You will be able to get the new v1.4 update on to your virgin iHub. 2. You will be able to get the new v1.4 update on to your v82.0 (bricked) iHub. 3. This...
  10. C

    down???

    am i the only one down been down since about 10 am est.
  11. BROWNNOSE

    [Tip:] Proper Proceedure for Rebooting your iLink IS-9000 Unit

    How to correctly reboot your IKS based system (in 7 magic steps) There are a lot of posts kicking around, concerning IKS enabled units losing their IP's ect and or getting disconnected from the 'net' so I thought that those having this type of issue, might benefit from knowing the correct...
  12. Scammer

    360 Premiere_0213_newlink

    360 Premiere_0213_newlink new fix **** Get in the habit of hard rebooting your receiver and giving it a minute AFTER the receiver reboots itself on loading .
  13. WizBang

    How to Boot a Viewsat Ultra Straight from USB

    I should have posted this the same time I posted the Ultra Lite posting....ooops. Viewsat Ultra, boot from USB How to Boot from Usb (frozen receiver) As long as receiver will power on and usb port functionally the following should eliminate the need to use the loader programs and null cable...
  14. hobo2

    [General Question?] dream box 500

    can any 1 tell me if the dream box 500 is running on dishnet ty hobo2
  15. H

    nvidia fx-5200 reboots PC. I have latest drivers. Is there any way to fix this issue? It is very irritating.?

    The nvidia FX-5200 video card has a problem in it. It reboots the PC everytime a graphics extensive application is run but after 15 min. of rebooting and waiting it works fine. I have downloaded the latest drivers and everything but this problem still persists. Is there any way in the world to...
  16. D

    Can someone post Ihub 1.4?

    The only thing I haven't tried is taking the hub from rom100 to 1.4, 1.9. and then 2.2 because I don't have the 1.4 file. I have taken it from rom100 to 1.9 then 2.2. It's the only thing I HAVEN'T TRIED.
  17. G

    [Problem!] After update with WF, Viewsat Ultra reboots to ---- then freezes up?

    After updating Viewsat and WF as instructed, the receiver reboots and freezes with ---- on display. If I unplug WF, then U.56 flashes on viewsat display and turns on. I plug in WF again and get no video and audio. Any help is appreciated. I have exhausted my options.
  18. P

    sonicview 8000 server

    Tried diffrent ip server and none seem to work. Says scrambled no service. Does any one have idea where to find working ip server address ? thanks been down for a while .update to wiz 2.2 file 512. any help is greatly appricated, thanks
  19. CASPER

    How to fix off service problem for all cnx models

    HOW TO FIX OFF SERVICE PROBLEM FOR ALL CNX MODELS C & P from my_cnx For cnx nano2 only -load latest factory using bootloader upgrade -then load npn 1.29npn receiver file after receiver reboot -check ip setup,make sure you got ip,then do iks registration -if iks registration say ok -then turn...
  20. CASPER

    How to fix off service problem for all cnx models

    HOW TO FIX OFF SERVICE PROBLEM FOR ALL CNX MODELS C & P from my_cnx For cnx nano2 only -load latest factory using bootloader upgrade -then load npn 1.29npn receiver file after receiver reboot -check ip setup,make sure you got ip,then do iks registration -if iks registration say ok -then turn...
Top