BROWNNOSE
BOOTLICKER
1. You will need to have an N3 cardserver account setup (RQCS is a good N3 cardshare server) or access to one from a friend over the internet. Softcam is not currently working for bev since it is N3 only.
2. Download and install MyTheatre 3.38 is a good version. DVBdream is a free alternative. Use the drivers the MyTheatre installed for your DVB card. You will need to find a MyTheatre FAQ to get to the point where you can see preview channels. Many howto guides are freely available for MyTheatre.
3. Download EmuNation-SC941.4.zip and extract it to your MyTheatre and /plugins directories as described in the included readme.txt. (someone please confirm this is the right emunation version for the job)
4. Install this small VC++ file from microsoft as described in the readme.txt from EmuNation-SC941.4.zip
http://www.microsoft.com/downloads/d...displaylang=en
5. R-click in MyTheatre where the video should be and select Plugins and enable EmuNation-SC with a checkmark.
6. Open cardclient.conf from /Plugins and remove the hash mark before the line that starts #newcamd . .
Edit in your rqcs (which is newcamd compatible) server info. Save and close.
7. Open EmuNation.ini in /Plugins. Edit this line:
[System Priorities]
Cardclient=-15
for N3 (bev) change to
Cardclient=-10
8. Open Softcam.key and paste the current bev keys in (I have not found a current source yet). I edited in some old keys from March that I found. I put the keys under providerID 0901, I saw on another site bev is now 0907, not sure
N 0901 00 79A98BCDA62B74EAF0C8854653311449
N 0901 01 0138B1F337FD46D68DF85377F9EE88BC
I used the Softcam.key file from EmuNation-SC941.3.zip as recommended from another site, not sure it makes a difference but here it is:
Code:
-----------------------
sc rev 939.6 ini file specs:
-----------------------
[EmuNation]
AuxEmu=1 ;Emulate Aux MAPROM (0=Use AuxServer for MAP Calls / 1=Use Cardless fix)
NADCWTweak=0 ;Send extra DCW (2,1,2) on channel change to prevent initial freeze
S_K_location= ;Alternate location of "softcam.key" file
UseCaCache=0 ;(0=update Softcam.key / 1=update Ca.Cache )
NorthAmerica=1 ; (1=North America any other value means not NA)
SmartCardPort=5 ;Serial port to use for smarcard, set to nonexistent port if no smartcard
[Menu Options]
Active=1 ;Turn Program on/off
BeepOnKeyFind=1 ;Beep On New Key (0=off / 1=on)
HideBadData=1 ;Do not display bad messages in monitor (0=off / 1=on)
KeepOldKeys=0 ;(0=just keep new key / 1=old key key and comment) used with Softcam.key file
LoadMonitorOnStart=0 ;Load Monitor on Startup (0=off / 1=on)
ProcessECM=1 ;Process ECM Packets (0=off / 1=on)
ProcessEMM=1 ;Process EMM Packets (0=off / 1=on)
ProcessPMT=0 ;Process PMT Packets (0=off / 1=on)
ProcessEmmS=1 ;If EMM-S keys exist, send for processing (0=off / 1=on)
ShowConsole=1
ShowDisassembly=0 ;(0=Basic / 1=Debug / 2=Verbose)
UseMaxParser=0 ;(0=Use old method / 1=Use New Parser)
SetClock=0 ;Set System Clock at startup 0=off, 1=on
[Logger]
LogPath= ;Path to use for ALL logging (default: {root}\Logs)
LogDCW=0
LogECMBin=0
LogEMMBin=0
LogECMText=0
LogEMMText=0
LogEMM-G=0 ;Log Decrypted EMM-G to file (0=off / 1=on)
LogEMM-S=0
LogRawEMM-S=0 ;If logging... Log Encrypted EMM-S Packets (0=off / 1=on)
LogConsole=0 ;Log Console Messages to file (0=off / 1=on)
LogMonitor=0
LogE3=1
[System Priorities]
Cardclient=-10
Conax=-15
ConstCW=-20
Irdeto=-15
Irdeto2=-12
Nagra=-15
Nagra2=-3
Nagra3=-10
PowerVU=-15
Seca=-19
Viaccess=-15
SC-Conax=-5
SC-Cryptoworks=-5
SC-Irdeto=-5
SC-Seca=-5
SC-Viaccess=-5
SC-Nagra=-15
[0101]
emm_pid_hex=0120 ;Hex value of PID for this provider
EMMOnChannelChange=1 ;Auto start EMM filter on channel change (1=Start autoroll every channel change/0=Start autoroll only when keys are invalid)
EMM_off_OnKeyFind=0 ;Stop EMM filter on key find (0=off / 1=on)
[0901]
emm_pid_hex=00EE ;Hex value of PID for this provider
EMMOnChannelChange=1 ;Auto start EMM filter on channel change (1=Start autoroll every channel change/0=Start autoroll only when keys are invalid)
EMM_off_OnKeyFind=0 ;Stop EMM filter on key find (0=off / 1=on)
[AuxServer]
Address=localhost
Port=7777
Password=password
[SC]
ShowEMM=0 ;Console Messaging of EMM MEssages (0=off/1=on)
ShowECM=0 ;Console Messaging of ECM Messages (0=off/1=on)
ShowRAWEMM=0 ;Console Messaging of Raw EMM Messages (0=off/1=on)
ShowRAWECM=0 ;Console Messaging of Raw ECM Messages (0=off/1=on)
ShowMAP=1 ;Console Messaging of MAP Calls (0=off/1=on)
ShowEMU=0 ;Console Messaging of EMU Details (0=off/1=on)
ShowKEY=1 ;Console Messaging of Key reads/writes (0=off/1=on)
ShowDISASM80=0 ;Console Messaging of Disassembly (0=off/1=on)
ShowCPUStats=0 ;Console Messaging of 6805 CPU Stats (0=off/1=on)
ShowCrypto=0 ;Console Messaging of Decryp Messaging (0=off/1=on)
ST19Echo=0 ;Set to 1 for ST19, 0 for real card
Dupes=0 ;0= don't allow duplicate messages to console, 1= allow them
CCDump=0 ;0=Do not print network traffic to console on smartcard and cardclient 1= do print9. I think that is all that needs to be done but my setup does not work. Perhaps it is a problem with the Softcam.key or maybe the cam bins in the /Plugins/Nagra folder need to be edited for bev? The EmuNation window looks ok but it says I am missing RSA keys- since DVB doesnt use an echostar receiver I dont think it should need any RSA configuration it should match the included bn102 by default. Please help me fill in the blanks where the red guy is banging his head against a wall. I will edit this post as I learn the answers.
--------------------------------------------------------------------------------
Last edited by realbigmike; 2009-05-28 at 18:56 PM.
2. Download and install MyTheatre 3.38 is a good version. DVBdream is a free alternative. Use the drivers the MyTheatre installed for your DVB card. You will need to find a MyTheatre FAQ to get to the point where you can see preview channels. Many howto guides are freely available for MyTheatre.
3. Download EmuNation-SC941.4.zip and extract it to your MyTheatre and /plugins directories as described in the included readme.txt. (someone please confirm this is the right emunation version for the job)
4. Install this small VC++ file from microsoft as described in the readme.txt from EmuNation-SC941.4.zip
http://www.microsoft.com/downloads/d...displaylang=en
5. R-click in MyTheatre where the video should be and select Plugins and enable EmuNation-SC with a checkmark.
6. Open cardclient.conf from /Plugins and remove the hash mark before the line that starts #newcamd . .
Edit in your rqcs (which is newcamd compatible) server info. Save and close.
7. Open EmuNation.ini in /Plugins. Edit this line:
[System Priorities]
Cardclient=-15
for N3 (bev) change to
Cardclient=-10
8. Open Softcam.key and paste the current bev keys in (I have not found a current source yet). I edited in some old keys from March that I found. I put the keys under providerID 0901, I saw on another site bev is now 0907, not sure
N 0901 00 79A98BCDA62B74EAF0C8854653311449
N 0901 01 0138B1F337FD46D68DF85377F9EE88BC
I used the Softcam.key file from EmuNation-SC941.3.zip as recommended from another site, not sure it makes a difference but here it is:
Code:
-----------------------
sc rev 939.6 ini file specs:
-----------------------
[EmuNation]
AuxEmu=1 ;Emulate Aux MAPROM (0=Use AuxServer for MAP Calls / 1=Use Cardless fix)
NADCWTweak=0 ;Send extra DCW (2,1,2) on channel change to prevent initial freeze
S_K_location= ;Alternate location of "softcam.key" file
UseCaCache=0 ;(0=update Softcam.key / 1=update Ca.Cache )
NorthAmerica=1 ; (1=North America any other value means not NA)
SmartCardPort=5 ;Serial port to use for smarcard, set to nonexistent port if no smartcard
[Menu Options]
Active=1 ;Turn Program on/off
BeepOnKeyFind=1 ;Beep On New Key (0=off / 1=on)
HideBadData=1 ;Do not display bad messages in monitor (0=off / 1=on)
KeepOldKeys=0 ;(0=just keep new key / 1=old key key and comment) used with Softcam.key file
LoadMonitorOnStart=0 ;Load Monitor on Startup (0=off / 1=on)
ProcessECM=1 ;Process ECM Packets (0=off / 1=on)
ProcessEMM=1 ;Process EMM Packets (0=off / 1=on)
ProcessPMT=0 ;Process PMT Packets (0=off / 1=on)
ProcessEmmS=1 ;If EMM-S keys exist, send for processing (0=off / 1=on)
ShowConsole=1
ShowDisassembly=0 ;(0=Basic / 1=Debug / 2=Verbose)
UseMaxParser=0 ;(0=Use old method / 1=Use New Parser)
SetClock=0 ;Set System Clock at startup 0=off, 1=on
[Logger]
LogPath= ;Path to use for ALL logging (default: {root}\Logs)
LogDCW=0
LogECMBin=0
LogEMMBin=0
LogECMText=0
LogEMMText=0
LogEMM-G=0 ;Log Decrypted EMM-G to file (0=off / 1=on)
LogEMM-S=0
LogRawEMM-S=0 ;If logging... Log Encrypted EMM-S Packets (0=off / 1=on)
LogConsole=0 ;Log Console Messages to file (0=off / 1=on)
LogMonitor=0
LogE3=1
[System Priorities]
Cardclient=-10
Conax=-15
ConstCW=-20
Irdeto=-15
Irdeto2=-12
Nagra=-15
Nagra2=-3
Nagra3=-10
PowerVU=-15
Seca=-19
Viaccess=-15
SC-Conax=-5
SC-Cryptoworks=-5
SC-Irdeto=-5
SC-Seca=-5
SC-Viaccess=-5
SC-Nagra=-15
[0101]
emm_pid_hex=0120 ;Hex value of PID for this provider
EMMOnChannelChange=1 ;Auto start EMM filter on channel change (1=Start autoroll every channel change/0=Start autoroll only when keys are invalid)
EMM_off_OnKeyFind=0 ;Stop EMM filter on key find (0=off / 1=on)
[0901]
emm_pid_hex=00EE ;Hex value of PID for this provider
EMMOnChannelChange=1 ;Auto start EMM filter on channel change (1=Start autoroll every channel change/0=Start autoroll only when keys are invalid)
EMM_off_OnKeyFind=0 ;Stop EMM filter on key find (0=off / 1=on)
[AuxServer]
Address=localhost
Port=7777
Password=password
[SC]
ShowEMM=0 ;Console Messaging of EMM MEssages (0=off/1=on)
ShowECM=0 ;Console Messaging of ECM Messages (0=off/1=on)
ShowRAWEMM=0 ;Console Messaging of Raw EMM Messages (0=off/1=on)
ShowRAWECM=0 ;Console Messaging of Raw ECM Messages (0=off/1=on)
ShowMAP=1 ;Console Messaging of MAP Calls (0=off/1=on)
ShowEMU=0 ;Console Messaging of EMU Details (0=off/1=on)
ShowKEY=1 ;Console Messaging of Key reads/writes (0=off/1=on)
ShowDISASM80=0 ;Console Messaging of Disassembly (0=off/1=on)
ShowCPUStats=0 ;Console Messaging of 6805 CPU Stats (0=off/1=on)
ShowCrypto=0 ;Console Messaging of Decryp Messaging (0=off/1=on)
ST19Echo=0 ;Set to 1 for ST19, 0 for real card
Dupes=0 ;0= don't allow duplicate messages to console, 1= allow them
CCDump=0 ;0=Do not print network traffic to console on smartcard and cardclient 1= do print9. I think that is all that needs to be done but my setup does not work. Perhaps it is a problem with the Softcam.key or maybe the cam bins in the /Plugins/Nagra folder need to be edited for bev? The EmuNation window looks ok but it says I am missing RSA keys- since DVB doesnt use an echostar receiver I dont think it should need any RSA configuration it should match the included bn102 by default. Please help me fill in the blanks where the red guy is banging his head against a wall. I will edit this post as I learn the answers.
--------------------------------------------------------------------------------
Last edited by realbigmike; 2009-05-28 at 18:56 PM.