BROWNNOSE
BOOTLICKER
How to correctly reboot your IKS based system (in 7 magic steps)
There are a lot of posts kicking around, concerning IKS enabled units losing their IP's ect and or getting disconnected from the 'net' so I thought that those having this type of issue, might benefit from knowing the correct order and proceedure for "Rebooting your IKS Equipment'
If you are experiencing connection issues with your iLink IS-9000 Unit ... and have ruled out weather conditions as a potential factor (i.e., Rain, Fog, and/or Heavy Snow for those of you who have that) ... not me, but for some I hear it can be a tremendous issue.
Here is what many have found can correct the issue.
Reboot all of the gear in your set-up in the order the signal comes into your house, so for those who might not understand what is being discussed here, here is a list:
Modem
Router
PC
Wireless Bridge (if using one)
Powerline Carrier Network Adapters (NetgearXE102's, HomePlug units ect ...)
iLink IS-9000
1) To reboot your modem, it is usually the easiest to, disconnect the AC adapter feeding your modem, and let it sit for about 30 seconds, then plug the AC line back into it. Once that has come back on-line fully (and the lights are ALL solid), then move on to the next piece of equipment - the router.
2) Now that you have rebooted the modem like a champ, the router should be no different. To reboot your router, folow the same proceedure as you had done with the modem. Disconnect the AC adapter feeding your router power, and let it sit for about 30-45 seconds. Afterwhich, plug the AC line back into it. Once the router has come back to life (fully), move on to the next piece of equipment - your PC.
3) Armed with a fresh IP from the modem, and a frehly rebooted router, its now time to reboot your PC. If you are running Windows, this means selecting, Start, then Shutdown (not restart).
Let the computer turn right off, and settle for a minute or so before turning it back on and rebooting it, this provides time for the electronics to bleed off any charges they might be holding (capacitors ect). Let the machine completely reboot and only then, move on to the next element which is either a wireless bridge is you are using one or the iLink IS-9000 itself.
4) If you are using a wirless bridge, unplug it, and let it rest for a minute. Then plug it back in and let it reboot completely. If you are not using a wireless bridge in your set up, you can skip this step, and move directly to Step 5.
5) If you are using any of the 'Wireless Powerline Network Adapters' like the Netgear XE102's, the HomePlug units or perhaps any of the 'Game Adapters' in your set up - follow these next instructions, otherwise jump ahead to Step 6. When rebooting the adapters, you'll want to reboot the one nearest your router first. To do that, remove it from the AC outlet and let it sit for about 1 minute, then plug it back in. Then, ahead of rebooting the iLink IS-9000 Unit (Step 6) repeat Step 5 again, for the 'Wireless Powerline Network Adapter' nearest the TV. Once it has been rebooted move on to Step 6.
6) Rebooting the iLink IS-9000: Turn the power off via the REAR switch. Let it sit for 2 mins. Turn the power back on, via the rear switch and let it boot up.
7) Using the remote and the on-screen menu system, ensure your Unit has an IP address. If it does you should have corrected all of your connectivity issues and should be good to go.
Happy testing
There are a lot of posts kicking around, concerning IKS enabled units losing their IP's ect and or getting disconnected from the 'net' so I thought that those having this type of issue, might benefit from knowing the correct order and proceedure for "Rebooting your IKS Equipment'
If you are experiencing connection issues with your iLink IS-9000 Unit ... and have ruled out weather conditions as a potential factor (i.e., Rain, Fog, and/or Heavy Snow for those of you who have that) ... not me, but for some I hear it can be a tremendous issue.
Here is what many have found can correct the issue.
Reboot all of the gear in your set-up in the order the signal comes into your house, so for those who might not understand what is being discussed here, here is a list:
Modem
Router
PC
Wireless Bridge (if using one)
Powerline Carrier Network Adapters (NetgearXE102's, HomePlug units ect ...)
iLink IS-9000
1) To reboot your modem, it is usually the easiest to, disconnect the AC adapter feeding your modem, and let it sit for about 30 seconds, then plug the AC line back into it. Once that has come back on-line fully (and the lights are ALL solid), then move on to the next piece of equipment - the router.
2) Now that you have rebooted the modem like a champ, the router should be no different. To reboot your router, folow the same proceedure as you had done with the modem. Disconnect the AC adapter feeding your router power, and let it sit for about 30-45 seconds. Afterwhich, plug the AC line back into it. Once the router has come back to life (fully), move on to the next piece of equipment - your PC.
3) Armed with a fresh IP from the modem, and a frehly rebooted router, its now time to reboot your PC. If you are running Windows, this means selecting, Start, then Shutdown (not restart).
Let the computer turn right off, and settle for a minute or so before turning it back on and rebooting it, this provides time for the electronics to bleed off any charges they might be holding (capacitors ect). Let the machine completely reboot and only then, move on to the next element which is either a wireless bridge is you are using one or the iLink IS-9000 itself.
4) If you are using a wirless bridge, unplug it, and let it rest for a minute. Then plug it back in and let it reboot completely. If you are not using a wireless bridge in your set up, you can skip this step, and move directly to Step 5.
5) If you are using any of the 'Wireless Powerline Network Adapters' like the Netgear XE102's, the HomePlug units or perhaps any of the 'Game Adapters' in your set up - follow these next instructions, otherwise jump ahead to Step 6. When rebooting the adapters, you'll want to reboot the one nearest your router first. To do that, remove it from the AC outlet and let it sit for about 1 minute, then plug it back in. Then, ahead of rebooting the iLink IS-9000 Unit (Step 6) repeat Step 5 again, for the 'Wireless Powerline Network Adapter' nearest the TV. Once it has been rebooted move on to Step 6.
6) Rebooting the iLink IS-9000: Turn the power off via the REAR switch. Let it sit for 2 mins. Turn the power back on, via the rear switch and let it boot up.
7) Using the remote and the on-screen menu system, ensure your Unit has an IP address. If it does you should have corrected all of your connectivity issues and should be good to go.
Happy testing
