CASPER
New member
r3x_2.0.1_newcam for Nfusion Nova/Neosat ipro 1000
Newcamd file for Nfusion Nova/Neosat ipro 1000
This is the latest version for Newcamd for the Nova \Neo
This Newcamd file works on the above mentioned it is
intended for the Protec 9600 sold in Europe the file is from
Europe as well but works.
Load the boot file in bootmode.
Load the bin file in Mainmode.
The bin file is from Europe so by default
it is in Pal mode and you will need to
change the Language as well in the Menu.
To change to multi mode from pal mode you will
need a picture to do that this will get you started
you will have to add the rest of the tp`s and sats you want
follow the following once you scan tune to one of the d*sh info
channels then change from pal to multi.
You need to create a user entry for each of your sats. In the "Installation" menu, Antenna Setting, Select Satellite
of USER1, setup "LNB type" User Def. "LO Freq.low" 11250 "LO Freq" 34463 (I entered 99999 but it switched to 34463
so we may need to change this MAX value in the bin to scan properly!) Select your diseqc port and "0/12v switch" 12v
Create one entry above as USERx entry for each sat you have
Next go into "Channel Search" and select your USERx entry. You need to add each transponder (Add TP) at the bottom.
Note it will not find all other transpondes using the network search option in the Add TP Window.
Enter Frequency 12296, Polarization Hor, and Symbol Rate 20000 for the user entry you created for sat 119 and scan for
channels. (remember the names are wrong but you could fix that later)
In the internet panel Set "Network Connection" OFF "Auto Update Check" OFF Select "NEWCAMD" ON (you may need to switch it from ON to OFF then back to ON then enter the numbers 9949 then Press OK. This brings up the NEWCAMD Server settings. Enter the data you need. Note one more problem here, if your server name has numbers in it you can not enter them (can not enter an IP address either) Turns out the option button to switch from Character entry to Numbers is controlled by a color button. The color buttons on the nfusion remote do not work in these screens. You may need to setup your home router for dynamic dns on the internet and point the nfusion to there (I did!) remember no numbers in the dns name. Restart the nfusion and test the channels on your private card.
This newer version bin added dn and b*v sats but you still need to add the tp`s
On the remote issue just use the numbers on the remote forget about the
changing the pad in the alpha \numeric option.
Newcamd file for Nfusion Nova/Neosat ipro 1000
This is the latest version for Newcamd for the Nova \Neo
This Newcamd file works on the above mentioned it is
intended for the Protec 9600 sold in Europe the file is from
Europe as well but works.
Load the boot file in bootmode.
Load the bin file in Mainmode.
The bin file is from Europe so by default
it is in Pal mode and you will need to
change the Language as well in the Menu.
To change to multi mode from pal mode you will
need a picture to do that this will get you started
you will have to add the rest of the tp`s and sats you want
follow the following once you scan tune to one of the d*sh info
channels then change from pal to multi.
You need to create a user entry for each of your sats. In the "Installation" menu, Antenna Setting, Select Satellite
of USER1, setup "LNB type" User Def. "LO Freq.low" 11250 "LO Freq" 34463 (I entered 99999 but it switched to 34463
so we may need to change this MAX value in the bin to scan properly!) Select your diseqc port and "0/12v switch" 12v
Create one entry above as USERx entry for each sat you have
Next go into "Channel Search" and select your USERx entry. You need to add each transponder (Add TP) at the bottom.
Note it will not find all other transpondes using the network search option in the Add TP Window.
Enter Frequency 12296, Polarization Hor, and Symbol Rate 20000 for the user entry you created for sat 119 and scan for
channels. (remember the names are wrong but you could fix that later)
In the internet panel Set "Network Connection" OFF "Auto Update Check" OFF Select "NEWCAMD" ON (you may need to switch it from ON to OFF then back to ON then enter the numbers 9949 then Press OK. This brings up the NEWCAMD Server settings. Enter the data you need. Note one more problem here, if your server name has numbers in it you can not enter them (can not enter an IP address either) Turns out the option button to switch from Character entry to Numbers is controlled by a color button. The color buttons on the nfusion remote do not work in these screens. You may need to setup your home router for dynamic dns on the internet and point the nfusion to there (I did!) remember no numbers in the dns name. Restart the nfusion and test the channels on your private card.
This newer version bin added dn and b*v sats but you still need to add the tp`s
On the remote issue just use the numbers on the remote forget about the
changing the pad in the alpha \numeric option.