A bit problem

[Josueis]

First hello guys!! Im from Puerto Rico.

I downloaded the latest bin for my CW600s Premiun, and the channels have a bit stubborn and the letters are blinking, I thought that the cables were wrong, and I check them out and the picture itself still blinking, but ican see the image clearly, but the letters are wrong. can anyone help me?

 

[CASPER]

before anything right down your sat settings , turn receiver off from the back leave off for about 3 minuets then turn back on, if that does not fix the problem, then do factory reset and re-scan your channels...butmake sure u write them down before going to reset...I had same problem couple of time 1st time it work with the hard boot, 2nd time with the rescaning channels after factory reset.....

 

[Josueis]

Sorry to ask sir, but how I do the reset?

 

[CASPER]

Read this before you do anything twice ...make sure you right down the settings you have right now, go to menu and find factory default then select all, this will delete existing channels, then you do a rescan of your sat's you can also Download and Unzip latest bin file.
and if you make a mistake you can also start fresh by

Transfer unzipped file onto USB stick then plug it into the box. You should see a message that says USB ready. Now press the USB button on remote and then scroll to the right to open the Software tab. Look for new file and press OK to load it. After it loads, it will ask you if you want to reboot, say YES.

When it reboots then go in menu and do a Factory Default. Then reboot again from the rear power switch. When it comes back up again, now you can setup satellites and options and rescan all satellites. After that is done, exit out of all menus and with the remote press F1 000 to enable the Patch. You should see a message on your tv that will say PATCH ENABLED. Now wait for keys to roll and watch tv.

Cable Instructions

To Prepare Receiver:
Turn off and attach the null-modem cable between the receiver and the computer serial port.Then plug in the power plug.
With the CaptiveWorks 700 receiver off, press the front power button and hold it.
While holding it, turn the rear toggle switch on, while STILL holding front power button.
You will see "boot" on the front display.

1. Download the current loader - New CW-700S Upgrade Loader and unzip
2. Download the latest bin and unzip this file
3. Load the latest bin with the current loader as per these instructions:
Open the loader, select the latest bin in the "File" bar across the top.
For Options, select Download S/W.
To select a port, choose your COM port (usually 1). Then hit the start/load and wait for the receiver to display "-end". At this point, turn receiver OFF from the rear switch to reboot.You can now follow the last paragraph in the above USB instructions to help setup satellites and scan channels.

Don't forget to Enable Patch F1 000

 

[CASPER]

if you are still in doubt check , others and mine, posting on how to's It should be in the receivers file sections depends on what receiver you are using....

 

[CASPER]

Are you tired of having to rescan sats, make changes to lnb and switch settings, readjust the TV picture settings and everything else that you have spent time adjusting everytime you do a new "bin" file upgrade???

Well, your problems are over, did you know that you can save ALL of your current settings easily by using one of the Menu features?

>Open the "Menu"
>"System Setting"
>"User Channel List"
then click on "Save..."

and save your current settings exactly the way they are, just be sure to have everything working the way you like it, then make up a short name such as "List 1" or any name you please and then Exit from the Menu and there you have it!

All of your settings are saved! Then after you do the next "bin" file upgrade, all you have to do is Load it and WaLa!!!

After the next "bin" file fix comes out, do the upgrade as usual, then:

Open the "Menu"
>"System Setting"
>"User Channel List"
then click on "Load..."

and select the name that you previously created (i.e. "List 1") then answer "yes" to load the stored settings, then Exit from the Menu once it has loaded the settings, it will now be exactly the way it was before, it will even pop up to the last channel you were watching when you saved the settings.

In the future when any changes have been made to your settings such as rescanning satellites for channel changes/updates or edits to anything imaginable, you can create another "Save..." list and every change will be saved in a new "User Channel List" file.

It only takes about 1 minute to "Load..." a saved list compared to all the grief of scanning satellites and making all the lnb and switch settings again.

I hope this will benefit all CWP owners, Enjoy!

 

[CASPER]

Be aware that sometimes the saved settings are corrupted and may not load back the same as before. It may take two or more saves to get a file that works, at worst. Then again, the first save may work, at best.

Also, if you tend to experiment with scanning channels on C-Band or standard Ku-Band, you may run across a signal that so totally corrupts and freezes your receiver that even the saved settings are corrupted and require a factory bin load and reset to factory settings to clear the memory.

Which is why:

Backing up your settings to your PC using the loader, every time you load a bin, is also a good precaution. This is done with the receiver in standby mode. Call it a backup of a backup, if you will. Press the Upload Data selection and they loader does the rest.

 

[CASPER]

1:You need Winrar,or Winzip to unzip the files,get it here:

2:The 1.06 loader to load the files,get it here:



3:Get the latest Bin File:Found in the Files Only Section.

4:Load the latest Bin File to the receiver in Standby Modelug the NULL Modem Cable into the nine pin port on the rear of the receiver.Turn the rear switch on,let it boot up,until you see the numbers on the led of the receiver(Either All O's,or Clock Numbers).Then press the on/off button on the front of the receiver,or the remote,and you should see this (Standby Mode)--+-- in the Led of the receiver.Press start on Loader 1.06.When finished cut rear switch off,disconnect Null Cable,hook receiver to dish and T.V.Turn rear switch bacck on.

5:Edit Transponder:


6:Go to Antenna Settings,enter all the correct settings,go back to top of page,press O.K. on remote,on the Sat you just set up,to store the settings to the receiver.

7:Easy Tuning:if you are scanning two sats,turn (Two)Status Keys on,three needs three,and four needs four.Enter the settings for each sat,Example:
Status------Sat Name-----Diseqc----LNB Freq.
ON--------110W----------LNB2-------11250


8:Scan the Sats,Fast Tuning(Preferred)or can aslo use Auto Tuning.

9:Set the time zone,make sureTime,and Date settings are correct.

10:Configure The SID Sort:Menu,System Setting,Channel NO.,NORMAL:Change to SID.

11:Exit menu to T.V.screen,Press F1,on remote then 000 to Enable Patch.

12:Wait for keys to roll,and watch T.V.



hope that everything I posted here helps you out

 

[Josueis]

Thanks for everything, but the mother board is dead, cant do anything