CASPER
New member
Fortec How To's - Take a Look!
--------------------------------------------------------------------------------
A MENU SETUP Below FOR 110 & 119 & Nimiq 1,3 91.0W SATELLITES WITH TWO SEPARATE LNB's & ONE DiSEqC OR A 22Khz SWITCH. Or A DISH PRO LNB, and no motor to move the dish
YOU MAY NEED TO FIX YOUR SATELLITE SETTINGS AFTER A FLASH & SET THE DEFAULT KEY.
The TP's below are close and will give you the channels that are there.
MENU to INSTALLATION then OK then OK in ANTENNA SETUP, then to the Satellite you want then OK.
----------------ECHO 7 = 119-----ECHO 8,10 = 110-Nimiq2=Nimiq 1,3 91.0W or Bev
LNB type --------- Standard ------------- Standard--------------Standard
LNB local-Freq ---- 11250------------------11250-----------------11250
22Khz -------------- ON----------------------Off--------------------OFF you can only have two satellites with this switch
DiSEqC -------------- 1------------------------2----------------------3
SKEW --------------- 0 -----------------------0----------------------0 this setting is if you don't have a motor to move the dish.
TP ------------ 12224V20.00-----------12224V20.000--------12224V20.000
Positioner Setting -- Disable----------------Disable--------------Disable
Satellite Scan ------ ALL----------------------ALL-------------------ALL
HOW TO SET DEFAULT KEY.
MENU, PARENTAL CONTROL, OK, down to SECOND PIN put in 0000 or 1010 or 1668 then OK then down to SET DEFAULT KEY then OK.
HOW TO DO A FACTORY SETTING
MENU, down to FACTORY SETTING then OK. When you do this you will clean out your channels.
AUTO-ROLL OPTIONS
You can turn auto-roll ON or OFF in DN, Bev & or GlobeCast. YOU NEED TO KEEP KEYCODE ON. Don't turn KEYCODE off or it will not look at any keys & TV will not work.
MENU then PARENTAL CONTROL then OK then to bottom at SECOND PIN then 1668 or 1010 or 0000
then down to AUTOROLL OPTIONS then OK. Side arrow will change autoroll then OK then EXIT.
To turn TP AUTOUPDATE ON or OFF go here. MENU, then down to USER SETUP then OK then down to TP AUTOUPDATE, side arrow will make the change. then EXIT. When TP auto-rolls it may give you all the channels on that TP and put them at the end of your channels. You may have to delete, rename or move them.
TIME SETTING & EPG ELECTRONIC PROGRAM GUIDE
Each time you turn the receiver ON you will be asked if you want the EPG. Click OK to download the EPG, this is the guide to tell you what is on TV. If you say EXIT you may only get one or two hours of the guide. If you need to refresh the EPG for any reason just turn the receiver OFF & ON from the front, but first make sure the time, date & day are correct. Use the remote number pad to change this. You need to be on 119 or 110 Satellite to download EPG. Will not work on Bev. After the guide download you can click on GUIDE then SIGNAL on the remote. You will get what is on that channel for several hours. If you have changed the Satellite name from ECHO to DISH you may not get asked if you want to download the EPG when you first turn on the receiver. More info on this under CHANNEL ORDER.
CHANNEL ORDER
If your channels are in a sid (channel) number order and not in the order you numbered them to be, do this. Put the word DUMMY as the first Satellite in the Satellite list with Channel Master. In CM right click on the word SATELLITE then click on ADD SATELLITE. Put DUMMY for the name then click OK. Now you need to move the word DUMMY from the bottom of the Satellite list to the top so it's the first one. Also you should change the word ECHO to DISH on each Satellite you are getting. Right click on the Satellite you want to change then click on PROPERTIES then change ECHO to DISH. You can save it in CM under Fortec Lifetime Ultra. If you change the ECHO name you may not get asked to download the EPG when you first turn on the receiver. More info on this under ELECTRONIC PROGRAM GUIDE & TIME SETTING.
--------------------------------------------------------------------------------
A MENU SETUP Below FOR 110 & 119 & Nimiq 1,3 91.0W SATELLITES WITH TWO SEPARATE LNB's & ONE DiSEqC OR A 22Khz SWITCH. Or A DISH PRO LNB, and no motor to move the dish
YOU MAY NEED TO FIX YOUR SATELLITE SETTINGS AFTER A FLASH & SET THE DEFAULT KEY.
The TP's below are close and will give you the channels that are there.
MENU to INSTALLATION then OK then OK in ANTENNA SETUP, then to the Satellite you want then OK.
----------------ECHO 7 = 119-----ECHO 8,10 = 110-Nimiq2=Nimiq 1,3 91.0W or Bev
LNB type --------- Standard ------------- Standard--------------Standard
LNB local-Freq ---- 11250------------------11250-----------------11250
22Khz -------------- ON----------------------Off--------------------OFF you can only have two satellites with this switch
DiSEqC -------------- 1------------------------2----------------------3
SKEW --------------- 0 -----------------------0----------------------0 this setting is if you don't have a motor to move the dish.
TP ------------ 12224V20.00-----------12224V20.000--------12224V20.000
Positioner Setting -- Disable----------------Disable--------------Disable
Satellite Scan ------ ALL----------------------ALL-------------------ALL
HOW TO SET DEFAULT KEY.
MENU, PARENTAL CONTROL, OK, down to SECOND PIN put in 0000 or 1010 or 1668 then OK then down to SET DEFAULT KEY then OK.
HOW TO DO A FACTORY SETTING
MENU, down to FACTORY SETTING then OK. When you do this you will clean out your channels.
AUTO-ROLL OPTIONS
You can turn auto-roll ON or OFF in DN, Bev & or GlobeCast. YOU NEED TO KEEP KEYCODE ON. Don't turn KEYCODE off or it will not look at any keys & TV will not work.
MENU then PARENTAL CONTROL then OK then to bottom at SECOND PIN then 1668 or 1010 or 0000
then down to AUTOROLL OPTIONS then OK. Side arrow will change autoroll then OK then EXIT.
To turn TP AUTOUPDATE ON or OFF go here. MENU, then down to USER SETUP then OK then down to TP AUTOUPDATE, side arrow will make the change. then EXIT. When TP auto-rolls it may give you all the channels on that TP and put them at the end of your channels. You may have to delete, rename or move them.
TIME SETTING & EPG ELECTRONIC PROGRAM GUIDE
Each time you turn the receiver ON you will be asked if you want the EPG. Click OK to download the EPG, this is the guide to tell you what is on TV. If you say EXIT you may only get one or two hours of the guide. If you need to refresh the EPG for any reason just turn the receiver OFF & ON from the front, but first make sure the time, date & day are correct. Use the remote number pad to change this. You need to be on 119 or 110 Satellite to download EPG. Will not work on Bev. After the guide download you can click on GUIDE then SIGNAL on the remote. You will get what is on that channel for several hours. If you have changed the Satellite name from ECHO to DISH you may not get asked if you want to download the EPG when you first turn on the receiver. More info on this under CHANNEL ORDER.
CHANNEL ORDER
If your channels are in a sid (channel) number order and not in the order you numbered them to be, do this. Put the word DUMMY as the first Satellite in the Satellite list with Channel Master. In CM right click on the word SATELLITE then click on ADD SATELLITE. Put DUMMY for the name then click OK. Now you need to move the word DUMMY from the bottom of the Satellite list to the top so it's the first one. Also you should change the word ECHO to DISH on each Satellite you are getting. Right click on the Satellite you want to change then click on PROPERTIES then change ECHO to DISH. You can save it in CM under Fortec Lifetime Ultra. If you change the ECHO name you may not get asked to download the EPG when you first turn on the receiver. More info on this under ELECTRONIC PROGRAM GUIDE & TIME SETTING.
