Hello
- Thread starter kenji
- Start date
CASPER
New member
Boot upgrade Guide for 2700A/E models from current b-70 to b-75.
=INSTRUCTIONS ================================================== ===============
1. Connect null modem cable from PC to receiver.
2. Open new [ Blacklist STB Updater Version 27.02 X-87BL.exe]. <--(Included in a Zip File)
3. Click Select File and open Boot_2700A (b75) _ (07)0310 new boot file. <--(Included in a Zip File)
4. Turn the receiver power ON and click Write File and wait until Download Completed OK will appear.
5. Front LED will display moving b-7-5 left to right if upgraded succeeded.
6. Open new api bin file matching with b75 boot version, <--(NEWEST ONE CAN BE FOUND IN OUR FILES SECTION)
(Any api version dated on or after Mar 10, 2007 and click Write File.
Wait until Download Completed OK appears.
Front LED will display b-7-5 and channel number will appear shortly.
If your receiver is in Factory Default Condition, front LED will appear ON shortly.
8. 2700A/E (IR) all models can be applied.
=NOTE(S) ================================================== ===================
1. Old version v27.01 will not work.
2. b75 boot upgrade needed only one time for each Receiver.
=INSTRUCTIONS ================================================== ===============
1. Connect null modem cable from PC to receiver.
2. Open new [ Blacklist STB Updater Version 27.02 X-87BL.exe]. <--(Included in a Zip File)
3. Click Select File and open Boot_2700A (b75) _ (07)0310 new boot file. <--(Included in a Zip File)
4. Turn the receiver power ON and click Write File and wait until Download Completed OK will appear.
5. Front LED will display moving b-7-5 left to right if upgraded succeeded.
6. Open new api bin file matching with b75 boot version, <--(NEWEST ONE CAN BE FOUND IN OUR FILES SECTION)
(Any api version dated on or after Mar 10, 2007 and click Write File.
Wait until Download Completed OK appears.
Front LED will display b-7-5 and channel number will appear shortly.
If your receiver is in Factory Default Condition, front LED will appear ON shortly.
8. 2700A/E (IR) all models can be applied.
=NOTE(S) ================================================== ===================
1. Old version v27.01 will not work.
2. b75 boot upgrade needed only one time for each Receiver.
CASPER
New member
How to flash the 2700A without deleting settings or channel list
This proceedure will keep you from deleting your antenna settings and your channel list once they are setup. I've seen this come up a number of times and thought I would post it in one place.
1. Turn the receiver off via the back switch.
2. Hook the null cable up between the pc and the receiver.
3. IMPORTANT!! Turn the receiver on via the back switch and WAIT for the receiver to boot all the way on. You should first see b-7 5 scroll across the receiver display then a quick blink 7.5 followed by On and then the last channel number that was selected.
4. Once you see the last channel number show on the receiver display then open up the loader, select the bin file and then download. Once the download complete pops up on your pc screen you should be good to go.
This will work when loading the factory bin as well. The only time you should loose the settings and the channel list is if you do a factory reset in the main menu of the receiver. You can even load the factory bin with the procedure above and once you see download complete popup on your pc screen then load the newest fix out and still not loose your settings or channel list. Hope this helps someone out.
This proceedure will keep you from deleting your antenna settings and your channel list once they are setup. I've seen this come up a number of times and thought I would post it in one place.
1. Turn the receiver off via the back switch.
2. Hook the null cable up between the pc and the receiver.
3. IMPORTANT!! Turn the receiver on via the back switch and WAIT for the receiver to boot all the way on. You should first see b-7 5 scroll across the receiver display then a quick blink 7.5 followed by On and then the last channel number that was selected.
4. Once you see the last channel number show on the receiver display then open up the loader, select the bin file and then download. Once the download complete pops up on your pc screen you should be good to go.
This will work when loading the factory bin as well. The only time you should loose the settings and the channel list is if you do a factory reset in the main menu of the receiver. You can even load the factory bin with the procedure above and once you see download complete popup on your pc screen then load the newest fix out and still not loose your settings or channel list. Hope this helps someone out.
CASPER
New member
Receiver Software update:
1. Connect the serial cable to the receiver and Comm #1 or Comm #2 port of your computer.
Double check and make sure the cable is securely connected.
Note: Pansat 2700 & 3500 use RS232C null modem(serial)cable and Pansat 2500 use RS232C straight through serial cable
2. Plug in the receiver power core, make sure the switch is turn to "ON " from the rear panel,
Then turn the power ON with remote control or from the front. You have to wait for receiver to boot up and
indicated ON.
3. Run the Down loader GTRom Loader from the new created folder.
4. Click the BIN FILE button, browser and select latest BIN FILE, then click the Open button.
5. Click the Download button, wait until the Download Completed.
Watch the LED on the receiver, it should reboot itself, wait until receiver displayed ON.
6. At this point; You are done with the software update. You can turn off power, then disconnect it from the PC.
================================================== ===
Receiver Configuration set up
With the Receiver unplug
1. Connecting all the RCA cable from the TV to the receiver, and connect RG-6 Cable to the receiver, then
Plug in power cord on the receiver.
2. You should see the Language Menu on the TV screen, select English.
3. "CAS SYSTEM" set up, just following the 3A, 3B and 3C steps
3A). Press menu, scroll down to select Parental Control then press OK.
3B). Scroll down to PIN #2, then enter you 4 digits password.0000
If you enter correct PW, it will take you into the CAS SYSTEM menu windown.
3C). In the CAS SYSTEM menu, scroll down to SET DEFAULT KEY, then press OK. Then exit to main menu page.
In the future; if you have to edit the Dishnet key, just following the step #3 to get into the CAS SYSTEM menu,
to edit the key go here Here is how to update key with a screen shoot
4. From the MAIN MENU: selecting INSTALLATION then Antenna setup Option.
Here is an example of dish set up and DiSeqC multi switch configuration;
DiSeqC #1 SuperDish Echo9-IA 13 Dishnet 121
DiSeqC #2 Echo8.6/Ku 110W,
DiSeqC #3 Echo7/Ku at 119W
Satellite: ECHO 9(121) same as dish 105
Lnb type-Standard
Lo freq-10750
22khz-OFF
DiseqC- #1
Skew: O
TP: leave it as is
Positioner-Disable.
Satellite: ECHO 6,8(110)
Lnb type-Standard
Lo freq-11250
22khz-OFF
DiseqC-#2
Skew: O
TP: leave it as is
Positioner-Disable.
Satellite: ECHO 7(119)
Lnb type-Standard
Lo freq-11250
22khz-OFF
DiseqC-#3
Skew: O
TP: leave it as is
Positioner-Disable.
5. Check the signal and Quality level highest as you can (adjust the dish slightly to improve the signal strength).
If you get no quality level on transponders, try others before giving up, because not all TPs are transmitting,
if nesscery Re-aim your dish still not getting any quality signal
6. Press the Exit button, press OK to save setting, the back to the Main Menu
7. Go back to the Installation Menu
8. Goto SATELLITE SCAN or BLIND SCAN, press OK, select the satellite to scan.
you have to scan all the satellites have, once it complete, you should be able to watching TV
9. WATCH TV!
1. Connect the serial cable to the receiver and Comm #1 or Comm #2 port of your computer.
Double check and make sure the cable is securely connected.
Note: Pansat 2700 & 3500 use RS232C null modem(serial)cable and Pansat 2500 use RS232C straight through serial cable
2. Plug in the receiver power core, make sure the switch is turn to "ON " from the rear panel,
Then turn the power ON with remote control or from the front. You have to wait for receiver to boot up and
indicated ON.
3. Run the Down loader GTRom Loader from the new created folder.
4. Click the BIN FILE button, browser and select latest BIN FILE, then click the Open button.
5. Click the Download button, wait until the Download Completed.
Watch the LED on the receiver, it should reboot itself, wait until receiver displayed ON.
6. At this point; You are done with the software update. You can turn off power, then disconnect it from the PC.
================================================== ===
Receiver Configuration set up
With the Receiver unplug
1. Connecting all the RCA cable from the TV to the receiver, and connect RG-6 Cable to the receiver, then
Plug in power cord on the receiver.
2. You should see the Language Menu on the TV screen, select English.
3. "CAS SYSTEM" set up, just following the 3A, 3B and 3C steps
3A). Press menu, scroll down to select Parental Control then press OK.
3B). Scroll down to PIN #2, then enter you 4 digits password.0000
If you enter correct PW, it will take you into the CAS SYSTEM menu windown.
3C). In the CAS SYSTEM menu, scroll down to SET DEFAULT KEY, then press OK. Then exit to main menu page.
In the future; if you have to edit the Dishnet key, just following the step #3 to get into the CAS SYSTEM menu,
to edit the key go here Here is how to update key with a screen shoot
4. From the MAIN MENU: selecting INSTALLATION then Antenna setup Option.
Here is an example of dish set up and DiSeqC multi switch configuration;
DiSeqC #1 SuperDish Echo9-IA 13 Dishnet 121
DiSeqC #2 Echo8.6/Ku 110W,
DiSeqC #3 Echo7/Ku at 119W
Satellite: ECHO 9(121) same as dish 105
Lnb type-Standard
Lo freq-10750
22khz-OFF
DiseqC- #1
Skew: O
TP: leave it as is
Positioner-Disable.
Satellite: ECHO 6,8(110)
Lnb type-Standard
Lo freq-11250
22khz-OFF
DiseqC-#2
Skew: O
TP: leave it as is
Positioner-Disable.
Satellite: ECHO 7(119)
Lnb type-Standard
Lo freq-11250
22khz-OFF
DiseqC-#3
Skew: O
TP: leave it as is
Positioner-Disable.
5. Check the signal and Quality level highest as you can (adjust the dish slightly to improve the signal strength).
If you get no quality level on transponders, try others before giving up, because not all TPs are transmitting,
if nesscery Re-aim your dish still not getting any quality signal
6. Press the Exit button, press OK to save setting, the back to the Main Menu
7. Go back to the Installation Menu
8. Goto SATELLITE SCAN or BLIND SCAN, press OK, select the satellite to scan.
you have to scan all the satellites have, once it complete, you should be able to watching TV
9. WATCH TV!
CASPER
New member
Loading Files to the Pansat 2700
***This applies to the original 2700, not the 2500 to 2700 conversions.
What I do is create a new folder called 'ps2700' on my PC to put all the files for this receiver. You should use the extract command or tab on your unzipping program (winrar) and extract the files to that folder. This puts the loader and all files in one easy to find place.
Download and unzip the GTRom Loader 27.02
Download and unzip the latest update file located in file section.
No other programs or software should be running on your computer
when loading files to your receiver.
1.) Turn your Pansat 2700 "OFF" with the rear power switch. If you have to move it to your computer, unplug it and then disconnect the satellite/TV cables last. The RG6 cables should always be connected/disconnected after powering down the receiver.
2.) Connect the RS232C (DB9) null modem cable to the receiver and Com1 port of your computer. (Use Com2 if not Com1 is not available). You must use a Null Modem serial cable, or a straight serial cable with a "null" adapter.
You can use a USB to serial adapter cable and plug your null cable into it or a null gender changer and the adapter alone, but you must load a USB to serial driver for it to work. If a driver CD did not come with your USB adapter cable, you can get a driver from:
Code:
USB Drivers (usb drivers,usb driver,download,usb device drivers,usb camera drivers,usbcam,webcam,camera,driver,universal serial bus,drivers,drvers,drivrs,files,file,usb adapter,usb port,usb hub, usb help,usb troubleshooting,driver archive,hardware dr
You have four com ports to choose from on the loader, but com port 1 is the default when the loader is opened. If you are using the USB adapter, the port number may be different from com port 1.
3). Plug in the receiver, Turn your 2700 "ON" with the rear switch, and see that “On� is showing on the LED on the receiver.
4). Run the GTRom Loader 27.02 from the folder on your PC.
5. Select 'App File' and select the latest update file by clicking 'Bin File.' A browser will open and you will locate the update file you unzipped in your folder. The file will be in this format:
X-87BL_000000_000_api .bin , then click the 'Open' button
6. Double check and make sure the cable is securely connected to your receiver and PC.
7. Click the 'Download' button, wait until the “Download Completed!!� is displayed. Watch the LED on the receiver, it should reboot itself, wait until the “On� display.
8). Wait for unit to finish the flash, DO NOT INTERRUPT THIS IN ANY WAY! It may take 15min for this file to transfer.
9). When receiver reboots and displays “On� wait a few more secs until you see the "Download Complete" popup on your PC. Many people unplug too soon!
You are now finished with the software update. Power off the receiver, unplug from power, disconnect from cable and computer.
***After connecting the receiver back to the TV/satellite cables and powering it back up, it may take up to 15-20min for the file to autoroll the keys. You can speed this up by setting it to channel 239 for D***n** or 410 for B***. I always go into 'antenna setup' in menu and verify that the settings are correct after loading a new file.
***This applies to the original 2700, not the 2500 to 2700 conversions.
What I do is create a new folder called 'ps2700' on my PC to put all the files for this receiver. You should use the extract command or tab on your unzipping program (winrar) and extract the files to that folder. This puts the loader and all files in one easy to find place.
Download and unzip the GTRom Loader 27.02
Download and unzip the latest update file located in file section.
No other programs or software should be running on your computer
when loading files to your receiver.
1.) Turn your Pansat 2700 "OFF" with the rear power switch. If you have to move it to your computer, unplug it and then disconnect the satellite/TV cables last. The RG6 cables should always be connected/disconnected after powering down the receiver.
2.) Connect the RS232C (DB9) null modem cable to the receiver and Com1 port of your computer. (Use Com2 if not Com1 is not available). You must use a Null Modem serial cable, or a straight serial cable with a "null" adapter.
You can use a USB to serial adapter cable and plug your null cable into it or a null gender changer and the adapter alone, but you must load a USB to serial driver for it to work. If a driver CD did not come with your USB adapter cable, you can get a driver from:
Code:
USB Drivers (usb drivers,usb driver,download,usb device drivers,usb camera drivers,usbcam,webcam,camera,driver,universal serial bus,drivers,drvers,drivrs,files,file,usb adapter,usb port,usb hub, usb help,usb troubleshooting,driver archive,hardware dr
You have four com ports to choose from on the loader, but com port 1 is the default when the loader is opened. If you are using the USB adapter, the port number may be different from com port 1.
3). Plug in the receiver, Turn your 2700 "ON" with the rear switch, and see that “On� is showing on the LED on the receiver.
4). Run the GTRom Loader 27.02 from the folder on your PC.
5. Select 'App File' and select the latest update file by clicking 'Bin File.' A browser will open and you will locate the update file you unzipped in your folder. The file will be in this format:
X-87BL_000000_000_api .bin , then click the 'Open' button
6. Double check and make sure the cable is securely connected to your receiver and PC.
7. Click the 'Download' button, wait until the “Download Completed!!� is displayed. Watch the LED on the receiver, it should reboot itself, wait until the “On� display.
8). Wait for unit to finish the flash, DO NOT INTERRUPT THIS IN ANY WAY! It may take 15min for this file to transfer.
9). When receiver reboots and displays “On� wait a few more secs until you see the "Download Complete" popup on your PC. Many people unplug too soon!
You are now finished with the software update. Power off the receiver, unplug from power, disconnect from cable and computer.
***After connecting the receiver back to the TV/satellite cables and powering it back up, it may take up to 15-20min for the file to autoroll the keys. You can speed this up by setting it to channel 239 for D***n** or 410 for B***. I always go into 'antenna setup' in menu and verify that the settings are correct after loading a new file.
Similar threads
- Locked
